ASME A112.19.8A-2008 Suction Fittings for Use in Swimming Pool, Wading Pools, Spas, Hot Tubs and Whirlpool
|
ID： |
0FA51631402545B5AEB733FF68127C10 |
|
文件大小(MB)： |
0.31 |
|
页数： |
18 |
|
文件格式： |
|
|
日期： |
2009-12-24 |
|
购买： |
文本摘录（文本识别可能有误，但文件阅览显示及打印正常，pdf文件可进行文字搜索定位）：
ASME A112.19.8a-2008,Addenda to,ASME A112.19.8-2007,Suction Fittings for Use in,Swimming Pools, Wading Pools,Spas, and Hot Tubs,AN A M E R I C A N NAT I O N A L STANDARD,J0118A,--`,,```,,,,````-`-`,,`,,`,`,,`---,Date of Issuance: August 29, 2008,ASME is the registered trademark of The American Society of Mechanical Engineers.,This code or standard was developed under procedures accredited as meeting the criteria for American National,Standards. The Standards Committee that approved the code or standard was balanced to assure that individuals from,competent and concerned interests have had an opportunity to participate. The proposed code or standard was made,available for public review and comment that provides an opportunity for additional public input from industry, academia,regulatory agencies, and the public-at-large.,ASME does not “approve,” “rate,” or “endorse” any item, construction, proprietary device, or activity.,ASME does not take any position with respect to the validity of any patent rights asserted in connection with any,items mentioned in this document, and does not undertake to insure anyone utilizing a standard against liability for,infringement of any applicable letters patent, nor assumes any such liability. Users of a code or standard are expressly,advised that determination of the validity of any such patent rights, and the risk of infringement of such rights, is,entirely their own responsibility.,Participation by federal agency representative(s) or person(s) affiliated with industry is not to be interpreted as,government or industry endorsement of this code or standard.,ASME accepts responsibility for only those interpretations of this document issued in accordance with the established,ASME procedures and policies, which precludes the issuance of interpretations by individuals.,No part of this document may be reproduced in any form,in an electronic retrieval system or otherwise,without the prior written permission of the publisher.,The American Society of Mechanical Engineers,Three Park Avenue, New York, NY 10016-5990,Copyright . 2008 by,THE AMERICAN SOCIETY OF MECHANICAL ENGINEERS,All rights reserved,Printed in U.S.A.,--`,,```,,,,````-`-`,,`,,`,`,,`---,ASME A112.19.8a-2008,Following approval by the ASME A112 Committee and ASME, and after public review, ASME,A112.19.8a-2008 was approved by the American National Standards Institute on August 11, 2008.,Addenda to the 2007 edition of ASME A112.19.8 are issued in the form of replacement pages.,Revisions, additions, and deletions are incorporated directly into the affected pages. It is advisable,however, that this page, the Addenda title and coyright pages, and all replaced pages be retained,for reference.,SUMMARY OF CHANGES,This is the first Addenda to be published to ASME A112.19.8-2007.,Replace or insert the pages listed. Changes given below are identified on the pages by a margin,note, (a08), placed next to the affected area. The pages not listed are the reverse sides of the,listed pages and contain no changes.,Page Location Change,1, 2 1.4 Revised,5–8.1 3.2 Revised in its entirety,3.3 First paragraph revised,3.3.1 Last paragraph revised,3.4 Second sentence revised,3.5.1 Last sentence revised,3.5.2 First sentence revised,3.6.1 First sentence revised,3.7 Title revised,3.7.1 Subparagraphs (a), (b), and (c) revised,3.8.1 Second and third lines revised,3.8.2 First sentence revised,3.9 Added,17, 18 7.1.1 Subparagraphs (a) and (b) corrected by,errata,(c),--`,,```,,,,````-`-`,,`,,`,`,,`---,INTENTIONALLY LEFT BLANK,(d),--`,,```,,,,````-`-`,,`,,`,`,,`---,ASME A112.19.8a-2008,SUCTION FITTINGS FOR USE IN SWIMMING POOLS, WADING,POOLS, SPAS, AND HOT TUBS,1 GENERAL,1.1 Scope,1.1.1 General Requirements. This Standard establishes,materials, testing, and marking requirements for,suction fittings that are designed to be totally submerged,for use in swimming pools, wading pools, spas, and hot,tubs, as well as other aquatic facilities.,1.1.2 Definition. Suction fittings shall be defined as,all components, including the sump and/or body,cover/grate, and hardware.,1.1.3 Compliance. Demonstration of compliance for,this Standard is merely an indication that the product,meets performance requirements and specifications contained,in this Standard.,1.1.4 Revisions. The provisions of this Standard,shall not be construed to prevent the use of any alternate,material or method of construction provided any such,alternate meets the full intent of the standard.,1.1.5 Exclusions,1.1.5.1 Skimmers shall be excluded from evaluation,to this Standard.,1.1.5.2 Vacuum connection covers shall be,excluded from evaluation to this Standard.,1.1.6 Ty……
……